This page covers: 2365, 2365A, A-PL-2365
Check the code on the back of your box, near the barcode.
Ages: 6 and up · About 30-60 minutes · Easy · Wipe-clean

Watch how it's done:

What's in your kit:

• 1 14 oz/412 mL Double-Wall Vacuum Insulated Tumbler, BPA-Free Cup and Lid
• 1 Turquoise Cord (85 cm)
• 1 Purple Cord (85 cm)
• 2 Cord End Caps
• 2 Strips of Tape
• 2 Round Metal Buckles
• 1 Silicone Ring
• 1 Silicone Straw Cover
• 1 Straw
• 1 Dark Turquoise Metallic Marker
• 1 Purple Metallic Marker
• 1 Design Stencil Sheet
• Written and Video Instructions Included

Before you start:

• Set up your work area first. Lay down paper towels to catch drips and spills.
• Lay out everything in the kit so it's all within reach before you begin.
  
• Remove all parts and craft supplies from the packaging.
• Check that the tumbler, straw, silicone ring, straw cover, cords, buckles, cord end caps, tape, metallic markers, and stencil sheet are included.
• Read the written instructions or watch the video instructions before beginning.
• Place the tumbler on a clean, dry, stable work surface.
• Make sure the outside of the tumbler is clean and completely dry before decorating.
• Keep small parts organized until they are needed.

Steps:

Step 1: Get Your Tumbler Ready

• Lay all your materials on a clean, flat surface.
• Take the silicone straw cover and gently push it up through the bottom of the lid until it pops into place.
• Press the silicone straw cover firmly onto the straw opening until it fits snugly.
• Stretch the silicone ring around the outside edge of the lid so it sits evenly.
• Set the tumbler aside while you make the handle.

Step 2: Make the Braided Handle

A. Prepare the Cords

• Lay the turquoise and purple cords next to each other.
• Fold the cords in half to find the middle.
• Push the folded middle straight through the wide opening of one cord end cap.
• Pull the cords through until a small loop remains on the other side.
• Tape the folded ends together so the cords stay bundled and are easier to push through the end cap.
• Take the large clear piece of the cord end cap, which is the tube.
• Push the taped cords into the open, smooth side of the tube.
• Pull the cords through until about 1 to 2 cm, or about the width of your fingernail, sticks out.
• Place the cords between the two small plastic arms of the small clear piece.
• Push the small clear piece into the tube.
• Twist it closed tightly.
• You should now have four loose strands hanging down.

Tip: Push as much cord as possible inside before twisting. The more cord inside, the tighter it will hold.

B. Braid the Cords

• Spread the four strands apart so you can see them clearly.
• Cross the two middle strands over each other to make an X. The strand on the right should cross over the strand on the left.
• Take the outside strand on the left and move it over one strand into the middle.
• Take the outside strand on the right and move it under one strand into the middle.
• Cross the two middle strands again to make another X, this time with the right strand crossing over the left.
• Move the left outside strand over one strand into the middle.
• Move the right outside strand under one strand into the middle.
• Keep repeating this pattern until your braid reaches the length you want.
• Gently pull the braid tight as you work so it stays neat and sturdy.

C. Finish the Braid

• Hold all four strands together at the end.
• Tape the ends together.
• Push the taped end into the open, smooth side of the large clear tube from the second cord end cap.
• Pull the cords through until about 1 to 2 cm sticks out.
• Place the cords between the two plastic arms of the small clear piece.
• Push the small clear piece into the tube.
• Twist tightly to lock it closed.

D. Add the Metal Buckles

• Clip one round metal buckle onto each cord end cap.

Step 3: Attach the Handle

• Clip the metal buckles onto the side loops of the silicone ring on the lid.
• Gently tug the handle to make sure everything is secure.
• If the handle feels tricky to close, hold the round metal clip while you grip and twist it.
• Turn the clip slowly and gently.
• If it does not close easily, pull it slightly back and try again.

Step 4: Decorate Your Tumbler

• Choose a design from the stencil sheet.
• Peel the stencil sticker from the sheet.
• Place it on the tumbler and press it down firmly.
• Use the metallic markers to color inside the stencil design.
• Carefully peel away the stencil to reveal your design.
• Let the ink dry completely before touching or using the tumbler.
• Add more designs, patterns, doodles, or your name if you like.
• You can reuse the stencil stickers. Peel them off slowly and gently, then place them back on the stencil sheet for next time.

Step 5: Fill, Sip, and Enjoy

• Twist the lid on tightly to seal the tumbler.
• To drink with the straw: Slide the cover on top of the lid so the straw opening lines up. Insert the straw through the opening and sip.
• To drink without the straw: Slide the cover on top of the lid again to open the drink spout. Sip directly from the lid.
• When you are finished, slide the cover back to close the opening and help prevent spills.
• Carry your tumbler by the handle and take it with you wherever you go.

Care Tips

• Hand wash with mild soap and water.
• Do not scrub over the marker designs.
• Do not microwave.
• Avoid leaving colored drinks inside for long periods.

Safety:

WARNING: Choking Hazard. Small Parts. Not for children under 3 years.

Prefer to print it?

Download the PDF instructions for DIY Kids Tumbler

Something missing or damaged?

Tell us the code on your box and what happened,
and we'll make it right. Get in touch.